Build a clearer vacuum cooler specification before quotation.
Use this engineering checklist to define product, load, temperature duty, throughput, installation conditions and automation requirements before comparing suppliers or requesting a final quotation.
Build a Vacuum Cooler Specification Before Requesting a Quote
This engineering worksheet is designed to help growers, packhouses and food processors define the information needed to size a vacuum cooler correctly before quotation. It reduces assumptions around chamber size, vacuum pump capacity, refrigeration duty, cycle time and site services.
1. Product and Throughput
- Product: crop or food product to be cooled
- Load per pallet: kg per pallet
- Pallet size: length × width × loaded height
- Pallets per batch: 1, 2, 4, 6, 8, 10, 12, 14, 16, 18 or 20
- Required batches per hour: target production rate
- Operating hours per day: expected daily utilisation
2. Cooling Duty
- Product entering temperature: °C
- Required final temperature: °C
- Maximum acceptable cycle time: minutes
- Estimated product moisture loss limit: % where relevant
- Product packaging: open crate, carton, bag, liner or other
For a meaningful equipment comparison, suppliers should state the assumed product mass, starting temperature, target temperature and guaranteed or estimated cycle time against the quoted refrigeration and vacuum-pump capacities.
3. Installation Conditions
- Country and site location: used for electrical, refrigerant and climate design
- Indoor or outdoor installation:
- Maximum ambient temperature: °C
- Available electrical supply: voltage, phase and frequency
- Available plant-room space: if pumps or refrigeration equipment are remote
- Drainage and water availability: where spray or washdown systems are required
4. Loading and Automation
- Manual pallet loading or conveyor loading
- Single-door or through-tunnel arrangement
- Automatic door operation
- Conveyor interface height and pallet-transfer requirements
- Forklift or pallet-truck access constraints
5. Controls and Options
- Multi-product HMI recipes
- Vacuum setpoint control
- Data logging and remote monitoring
- Additional HMI languages
- Water spray or humidification where suitable for the product
- Stainless internal finishes and upgraded external corrosion protection
- Spare probes, door seal and service kit
6. Supplier Comparison Checklist
When comparing quotations, request the following on a like-for-like basis:
- Vacuum pump manufacturer, model and nominal pumping capacity
- Refrigeration compressor manufacturer and model
- Refrigeration duty at the quoted design ambient
- Evaporator arrangement and refrigerant
- Electrical standard and installed power
- Chamber internal dimensions and usable pallet envelope
- Estimated or guaranteed cycle time for the stated product load
- General arrangement drawing
- Steel grades and corrosion-protection specification
- Warranty, commissioning support and recommended spares
Engineering Review
Vacuum Cooling Group can use this information to review the application and prepare a machine specification around the required product load and production rate rather than selecting equipment from pallet count alone.
Information to Send With an RFQ
Product:
Country:
Pallet size:
kg per pallet:
Pallets per batch:
Entering temperature:
Target temperature:
Required cycle time:
Cycles per hour:
Hours per day:
Indoor / outdoor:
Electrical supply:
Manual / conveyor loading:
Other requirements:
Check the project with the supporting tools.
A pallet count alone is not enough for final equipment selection. Use the planning resources below to test throughput, heat load and process assumptions before engineering review.
Vacuum Cooler Sizing Calculator
Estimate the pallet positions required from peak production flow and complete cycle interval.
Open sizing calculator → Production planningThroughput Calculator
Translate batch size and cycle duration into hourly and daily production capacity.
Open throughput calculator → Thermal engineeringRefrigeration Duty Guide
Estimate preliminary product heat load before the refrigeration package is selected.
Open engineering guide → Acceptance planningFAT & Commissioning Checklist
Turn the agreed specification into measurable FAT, SAT, loaded-trial and sign-off criteria before dispatch and handover.
Open acceptance checklist →Send the completed specification with the real operating data.
Include product, packaging, pallet or trolley dimensions, batch mass, entering and target temperatures, production rate, installation country, electrical supply and loading method.